• External temperature sensor with 2 meter cable.
• 2.5 mm plug that fits the models Ontech GSM 9035 Ontech GSM 9040 and Ontech Relay 9015.

• When connected to Ontech GSM 9025, remove the plug and connect the cables to the screw terminal. Accuracy +/- 1 degree C.

• The cable can be extended up to 10 meters.

• Lithium ion battery 3,7  volt 1000 mAh.
• Are buult-in in the models 9025, 9035 och 9040.

• Can also connect to models 9020 and 9030
• Necessary for the power failure alarm function.

• Keeps the device alive 10 to 20 hours after power failure.

Heating

• Connect the Ontech GSM 9025’s potential-free relay toa three phase relay in the main powerfuse box and control the heat throughout the entire cabin.
• Control fixed installed radiators (electric elements and heat fans).
• Connect up to seven wireless Ontech Relay 9015 extra relays s and control the heat individually in many room via controllable 230V outputs.

Other applications

• The potential-free relay can connect any type of electrical control up to 230V / 10A. This can be pumps, ventilation, motors, etc.
• A special feature for using the device to open ports by command or simple phone dialing is available. This causes the remote control to open the garage door becomes redundant. It has moved into the mobile phone.
• The potential-free relay can be set with timer function so it turns on or off after the set time.
  

  ---

Alarms

• Connect different types of alarms to the two alarm inputs of the Ontech GSM 9025. The alarm inputs can be set to alert when the circuit opens or closes.
• All alarms with relay outputs can be connected, such as motion detectors (PIR), fire alarms, magnetic switches, level guards, pedal mats, etc.
• Alarm sensors which gives or breaks voltage 3-30V in case of alarm can also be connected.
• Connect the Ontech Relay 9015  wireless devices and Ontech Alarmbox 9012 to the alarm transmitter and send the signal wirelessly to the Ontech GSM 9040. There is no need for long cable wiring.
• The alarm inputs can be set with delay.
  

  ---

Temperature

• Ontech GSM 9025 reports the current temperature. The Ontech Control control panel automatically updates  so you can see the current temperature at all times.
• An external temperature sensor with 2 meter cable  can be connected and then the temperature is reported for both the internal temperature sensor and the external.
• Temperature alarm can be set as alarm when the temperature is below and / or exceeds the alarm limits set by the users.
  

  ---

Operating the device

• The device is controlled with the Ontech Control web panel. This is by far the easiest and easiest way to control and communicate with Ontech GSM 9040. More information here. SIM card for this is included and the first month free of charge.

• The device can also be controlled by SMS or with an app that uses SMS. A SIM card is required. All GSM operators work but not clean 3G providers such as the operator Tre, hallon.se or Wifog. With apps for Android and Iphone, the use can be simplified by SMS control.

Main power monitoring

• Ontech GSM 9025 has built-in backup battery that is enough to keep the device alive 10-20 hours. Useful when the device is used as an power fail alarm.
• The device alerts to all names in the alarm list when a power failure occurs and announces when power is returned.
  

  ---

GPS

• Optionally, a GPS receiver can be connected to the device. The device reports position, speed and direction.
• Alarms can be set to be activated when the device is outside a preset distance away from the GPS fence.
  

  ---

More

• The device is encased in line with the IP65 which is suitable for tough environments and outdoors.
• The device is powered by 12-24 VDC. Power adapter for 230V included.
• There is a setting that allows the potential-free relay to turn on or off at alarm.
• It is possible to measure current 4-20 mA or voltage 0-10 V and get the values reported. You can also set alarms when limit values are exceeded or lowered.
• The device alerts via email. As an option, SMS can be requested for alarm.
  

  ---

Functions

• Ontech IR 9016 connects to Ontech GSM 9040.
• Air heat pumps are controlled via Ontech Control or SMS or Android app wherever you are.
• Set temperature, mode and fan.

• Fits the major brands of air heat pumps on the market. A detailed list can be found here.
• The last software is available for download on the product page for Ontech GSM 9040.
• Updating is easy by connecting the supplied USB cable to a Windows computer.

• The device communicates with the main unit with a short-range radio frequency of 2.4 GHz. Up to 7 Ontech GSM Relay can be connected and controlled individually to each main unit.
• The unit has a 230V outlet that can be switched on and off by any of the main devices such as elements, pumps, etc.. The power supply can be delayed, from 1 second to 99 hours.
• The unit has a built-in temperature sensor. An external temperature sensor can be connected. This is an optional accessory and is not included. Upon request, the unit reports the temperature.

• The unit can be set to alert if the temperature exceeds or falls below a preset temperature.
• The unit can be used as a thermostat if one element is connected to the 230 V socket.
• The device has two wired alarm inputs. These can be set to end up (Normally Open, NO) or Breaking Function (Normally Closed, NC). Various types of alarms can be connected to these, such as fire alarms, motion detectors, level detectors, etc.

• Easy to install. Put the device into a wall outlet and it automatically contacts the main unit and registers in the Ontech system.
• The range is approximately 30 meters in the free field. This is usually enough for a normal sized villa. The devices also function as “repeaters”, ie they forward the radio signal to the main unit from devices further away. This increases the range of the system.

Heating

• Connect a radiator (electric radiator or heater fan) to the Ontech GSM 9040 to control the heat in the room.
• Connect up to seven wireless Ontech Relay 9015 extra relays s and control the heat individually in many room via controllable 230V outputs.
• Use the thermostat function to automatically keep the heat at a certain level in the rooms or the entire cabin. Connect the Ontech GSM 9040 to control a contactor in the power supply and control the heat throughout the cabin.
• With the Ontech IR 9016 accessory, move the air heat pump remote control to your phone / tablet / computer.

Other applications

• The 230V output can connect any type of electrical control up to 230V / 16A. This may be servers, routers, pumps, ventilation, motors etc.
• A special feature for using the device to open ports by command or simple dial from telephone available. This causes the remote control to open the garage door becomes redundant. It has moved into the mobile phone.
• The 230V output can be set with timer function so it turns on or off after the set time..

Alarms

• Connect different types of alarms to the two alarm inputs of the Ontech GSM 9040. The alarm inputs can be set to alert when the circuit  closes or opens.
• All alarms with relay output can be connected, such as motion detectors (PIR), fire alarms, magnetic switches, level guards, pedal mats etc.
• Alarm transmitters which close or opens  voltage 3-30V in case of alarm can also be connected
• Connect the Ontech Relay 9015 Wireless Ontech Relay 9015 and Ontech Alarmbox 9012 to the alarm transmitter and send the signal wirelessly to the Ontech GSM 9040. There is no need for long cabling.
• The alarm inputs can be set with delay.

Temperature

• Ontech GSM 9040 reports the current temperature. The Ontech Control control panel automatically updates  so you can see the current temperature at all times.
• An external temperature sensor with 2 meter cable  can be connected and then the temperature is reported for both the internal temperature sensor and the external.
• Temperature alarm can be set as alarm when the temperature is below and / or exceeds the alarm limits set by the users.

Operating the device

• The device is controlled with the Ontech Control web panel. This is by far the easiest and easiest way to control and communicate with Ontech GSM 9040. More information here. SIM card for this is included and the first month free of charge.

• The device can also be controlled by SMS or with an app that uses SMS. A SIM card is required. All GSM operators work but not clean 3G providers such as the operator Tre, Hallon.se or Wifog. With apps for Android and Iphone, the use can be simplified by SMS control.

Main power monitoring

• Ontech GSM 9025 has built-in backup battery that is enough to keep the device alive 10-20 hours. Useful when the device is used as an power fail alarm.
• The device alerts to all names in the alarm list when a power failure occurs and announces when power is returned.

More

• There is a setting that allows the 230V output to turn on or off at alarm.
• It is possible to measure current 4-20 mA or voltage 0-10 V and get the values reported.
• You can also set alarms when limit values are exceeded or lowered. The device alerts via email. Optionally, SMS can be requested for alarm.
  

  ---